Step by Step Guide to Resetting an RCD in the UK
When the lights go out or a row of sockets suddenly dies, the RCD in your consumer unit may have tripped. That can feel worrying, especially if you are not used to looking inside a fuse box. The good news is that resetting an RCD is often simple, as long as you take it slowly and stop if anything seems unsafe.
An RCD, or Residual Current Device, is a safety device designed to cut power quickly when it detects electricity leaking to earth. That kind of fault can happen with a damaged appliance, water getting into outdoor electrics, faulty wiring, or sometimes a temporary surge.
This guide explains how to reset an RCD in a typical UK home, how to find what caused it to trip, and when to call a qualified electrician instead of trying again.

What an RCD does and why it trips
An RCD monitors the flow of electricity in a circuit. In normal use, the electricity going out should match the electricity coming back. If there is a mismatch, the RCD assumes some current may be leaking somewhere it should not, such as through a damaged cable, a wet outdoor fitting, or a faulty appliance.
When that happens, the RCD trips and cuts the supply to the circuits it protects.
In many UK homes, an RCD may protect several circuits at once. For example, one RCD might cover downstairs sockets, upstairs sockets, and the kitchen. Newer consumer units may use RCBOs, which combine overcurrent and residual current protection for individual circuits.
That means the exact layout may vary, but the basic reset process is similar.
Before you touch anything, remember this:
If the RCD trips again straight away, it is doing its job. Do not keep forcing it back on.
Repeated tripping means there is likely still a fault present. Resetting once is fine. Resetting again after isolating appliances may be fine. Repeated attempts without finding the cause are not.
Before you start, check these safety points
Working around a consumer unit can be safe if you only operate the switches from the outside. Do not remove covers, loosen screws, touch exposed wiring, or try to repair anything inside.
Stop immediately and call a qualified electrician if you notice:
A burning smell
Buzzing or crackling from the consumer unit
Scorch marks or melted plastic
A switch that feels hot
Water near the consumer unit
A damaged socket, plug, or cable
An RCD that will not stay on even after everything is unplugged
Also be careful if the trip has affected medical equipment, stair lifts, freezers, security systems, or heating controls. If there is any risk to safety or wellbeing, get help promptly.
You will not need tools for a basic reset. You only need access to the consumer unit and, ideally, a torch if the lights are off.
Step 1. Find the consumer unit
In the UK, the consumer unit is often found in one of these places:
Hallway cupboard
Under the stairs
Utility room
Garage
Kitchen cupboard
Near the electricity meter
Open the cover if it has a plastic flap. You should see a row of switches. These may be labelled with circuit names such as:
Lights
Sockets
Kitchen
Cooker
Shower
Immersion heater
Garage
Outside sockets
You may also see one or more larger switches labelled `RCD`, `Main Switch`, or `Test`.
The RCD often has a small test button marked `T` or `Test`. Do not press the test button yet if you are trying to restore power. The test button is for checking that the RCD trips correctly.
Step 2. Identify the tripped RCD
Look at the position of the switches. Most switches are on when they point upwards, but not every unit is the same. Many consumer units have markings such as `I` for on and `O` for off.
A tripped RCD may sit:
Fully down in the off position
Halfway between on and off
Slightly different from the switches beside it
If the switch is in the middle, push it fully to the off position first. Some RCDs will not reset properly unless you do this.
If only one small circuit breaker has tripped, rather than the RCD, the fault may be on that individual circuit. The process is similar, but this guide focuses on the RCD.
Step 3. Switch off the circuit breakers protected by that RCD
Before resetting the RCD, switch off the smaller circuit breakers controlled by it. These are usually the MCBs lined up next to or after the RCD.
This matters because a faulty appliance or circuit may still be connected. Switching the circuits off first gives you a cleaner reset and helps you narrow down the fault.
If your consumer unit has two RCDs, try to work out which circuits are grouped with the tripped one. The labels or layout may help. If the labels are unclear, take your time. Do not guess wildly or force switches.
A simple approach is:
Leave the main switch alone unless you need to turn off all power.
Find the tripped RCD.
Switch off the smaller breakers that sit under that RCD’s section.
Keep a note of anything that was already off.
If your consumer unit uses individual RCBOs instead of shared RCDs, you may only need to reset the single tripped device.
Step 4. Reset the RCD
Now push the RCD fully into the off position, then firmly back to on.
Use steady pressure. You should not need excessive force. If it feels stuck, loose, broken, or unusually stiff, stop.
If the RCD stays on while the circuit breakers are off, that is a useful sign. It suggests the RCD itself may be capable of resetting, and the problem may be on one of the circuits or plugged-in items.
If the RCD will not reset even with the protected circuits switched off, do not keep trying. The fault may be in the consumer unit, the RCD, or the fixed wiring. Call a qualified electrician.

Step 5. Turn the circuit breakers back on one by one
If the RCD has stayed on, switch the circuit breakers back on one at a time.
Wait a few seconds between each one. This helps you spot which circuit causes the RCD to trip.
For example:
Turn on the lighting circuit.
Wait briefly.
Turn on the upstairs sockets.
Wait briefly.
Turn on the kitchen sockets.
Continue until the RCD trips or all circuits are back on.
If the RCD trips when you switch one circuit back on, you have narrowed the issue down. Leave that circuit off and turn the others back on, if they stay on safely.
Common problem circuits include kitchen sockets, outdoor sockets, garage supplies, immersion heaters, showers, and circuits with appliances that use water or heat.
Step 6. Unplug appliances on the problem circuit
If a socket circuit appears to be the cause, unplug appliances on that circuit before trying again.
Do not just switch them off at the socket. Unplug them fully where possible. Some faults can still be present when an appliance is plugged in, depending on the appliance and socket arrangement.
Pay close attention to items such as:
Kettles
Toasters
Washing machines
Dishwashers
Tumble dryers
Fridges and freezers
Extension leads
Outdoor equipment
Fish tank heaters and pumps
Portable heaters
Boilers and heating controls
EV charging equipment plugged into a socket
Once everything on that circuit is unplugged, reset the RCD again and turn the circuit breaker back on.
If the RCD now stays on, one of the unplugged appliances is likely the cause.
Step 7. Plug appliances back in carefully
Plug appliances back in one at a time. After each one, wait a moment.
If the RCD trips as soon as one appliance is plugged in or switched on, stop using that appliance. Unplug it and label it so no one else uses it by mistake.
Do not test a suspect appliance over and over. A faulty appliance can be dangerous, especially if it has heating elements, water inside, or visible cable damage.
Common examples include:
A kettle that trips the RCD when it boils
The heating element may be failing, or moisture may have entered the base.
A washing machine that trips mid-cycle
The fault may appear only when it heats water, drains, or spins.
Outdoor lights that trip after rain
Water may have entered a fitting, junction box, or cable.
A freezer in a garage that trips the supply
The freezer, socket, extension lead, or garage wiring may need checking.
If the appliance is valuable or hard-wired, arrange a repair by a competent person. If it is damaged or old, replacement may be safer.
Step 8. Check for obvious causes around the home
Sometimes the cause of an RCD trip is obvious once you look around.
Check for:
A cable trapped under furniture
A plug that feels warm
A cracked socket faceplate
Water near outdoor sockets
Rainwater in garden lighting
An overloaded or damaged extension lead
A DIY job recently carried out nearby
A bulb or fitting that failed with a bang
Rodent damage in garages, sheds, or loft spaces
If the trip happened during heavy rain, outdoor electrics are a strong possibility. Garage supplies, pond pumps, garden sockets, and exterior lights often show faults when damp gets in.
If the trip happened while using a specific appliance, start there.
If the trip happened overnight, look at appliances that run automatically, such as fridges, freezers, boilers, immersion heaters, and heating controls.
Step 9. Leave the faulty circuit off if needed
If one circuit keeps tripping the RCD and you cannot identify a safe cause, leave that circuit switched off. You may still be able to restore power to the rest of the property.
For example, if the garage circuit trips the RCD but the house sockets and lights stay on, keep the garage circuit off and arrange an inspection.
Do not run extension leads around the home as a long-term workaround. Extension leads can create trip hazards, overload risks, and new electrical problems if used incorrectly.
If the affected circuit supplies something essential, such as heating, hot water, or refrigeration, call for professional help sooner rather than later.
When you should call an electrician
A one-off RCD trip is often not an emergency. A trip that keeps coming back needs proper attention.
Call a qualified electrician if:
The RCD will not reset
The RCD trips with all appliances unplugged
The same circuit trips repeatedly
You see damage, heat, smoke, or scorching
The consumer unit has no clear labels
Outdoor electrics are involved
A hard-wired appliance is suspected
The property has old wiring
You feel unsure at any point
In the UK, electrical work in homes must be carried out safely and may need to comply with Building Regulations. For consumer unit work, new circuits, or fixed wiring repairs, use a competent electrician.
A professional can carry out testing that a homeowner cannot do safely, including insulation resistance testing, RCD trip time testing, and fault finding on fixed wiring.
How to reduce future RCD trips
You cannot prevent every fault, but a few habits help.
Keep outdoor electrics in good condition. Use weatherproof fittings where suitable, and avoid leaving temporary extension leads outside. If an outdoor socket cover is cracked or loose, get it replaced.
Do not overload sockets. A multiway extension lead should not be used for several high-power appliances at once. Kettles, heaters, tumble dryers, and washing machines draw a lot of current.
Replace damaged leads. If a cable is frayed, crushed, split, or has exposed inner cores, stop using it.
Be careful with water. Appliances that mix electricity and water, such as washing machines, dishwashers, steam cleaners, and outdoor pumps, deserve extra attention if they trip an RCD.
Label your consumer unit. Clear labels make future fault finding quicker and safer. If your labels are missing or wrong, ask an electrician to identify the circuits properly during a visit.
Use the test button as recommended by the manufacturer or the label on your consumer unit. Pressing the test button should trip the RCD. You then reset it in the normal way. Only do this at a sensible time, when losing power briefly will not cause a problem.
What a successful reset looks like
A successful reset is simple:
The RCD stays in the on position.
The circuit breakers turn back on without tripping it.
Lights, sockets, and appliances work normally.
There is no smell, heat, noise, or visible damage.
The same fault does not return.
If the RCD trips again, treat that as useful information. It is not an inconvenience to ignore. It is a warning that something needs isolating, repairing, or replacing.
The safest approach is to reset once, narrow the fault down step by step, and stop if the cause is not clear. An RCD protects people from electric shock, so when it refuses to stay on, listen to it.


